Customer Reviews

4.85 out of 5
See all 217 reviews
Write a Review
  • All Reviews (217)
  • Image (51)
  • Video (2)
  • All Star
    • All Star(217)
    • 5 Star(196)
    • 4 Star(15)
    • 3 Star(2)
    • 2 Star(2)
    • 1 Star(2)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (United States)
|
Show Original

A part of the review has been auto-translated.

  • 11/01/2020

    This is my first 3D printer but I have choosed it after viewing many youtube video and read many things about this and the A20M The A10M is cheapest than the A20M and the coast difference does not equal the quality evolution, it is why I have bought the A10M ! Now, the indications to assemble it are not perfect but it's easy to guess what to do except for inserting the filaments in the extrudors. I have spent many minuts to do it... I have updated the firmware to Marlin 1.1.9, then, the filaments had to go to the noze. I have printed the dog (from file on the 8G sd card) : the quality is good but it was very difficult to remove it from the bed. I have placed an order for a better bed.

    Comments (1)
    Show Original
  • 23/10/2020

    received the printer is great packing. the spindle holders don't have any screws etc. the screen died mid way printing sample file. instructions are not clear on the assembling. but print quality is superb.

    Comments
    Show Original
  • 07/01/2019

    So far so good, i have not had any issues printing yet, the build was pretty straight forward, but I did have to straighten out the x carriage a bit before it would sit properly on the x axis. but other than that, it was very easy. Most of the issues I have had are with the slicing software, which is not a reflection on the hardware, as the test prints worked great. :) A very good printer. Not really for the beginner though,

    Comments
    Show Original
  • 13/05/2019

    Voici la liste des problèmes et changement que j’ai du apporter sur la Gtech A10M que j’ai acheté la semaine dernière avant de commencer l’impression. Un des 2 tubes PTFE était brisé et changé avec l’un des deux fournis. Les axes X et Y du chassis n’étaient pas à 90 degré l’un de l’autre ,corrigé en dévissant les 4 vis du joint central et en se servant de l’équerre pour replacé à 90 degré,comme il faut. L’axe X , les roulements étaient très mal ajustés il était impossible d’obtenir un niveau horizontal parfait, avec beaucoup d’effort en replaçant les roulements tout est revenu à l’état normal. Le ventilateur du bloc d’alimentation 24v est très bruyant ainsi que ceux de l’extruder. Le plateau chauffant est bombé de 1,3mm. entre les coins et le centre du plateau. Pas de plaque de verre fournie tel que montré sur photo de publicité Geeetech et Banggood. Un lot de vis est fourni en quantité presque industriel mais je vais y trouver un endroit ou les utilisés. Deux buses sont fournis avec mon imprimante, une de plus que prévus. Une seule feuille de montage était fournie, pour le manuel de l’utilisateur il faut se référer au site de Gtech. Pour la qualité d’impression et les modifications apportés à l’imprimante celle ci est de qualité ordinaire, le bltouch de tech pourrait il améliorer l’impression??? Pour la plaque de verre ,est ce que je peux m’attendre que Geeetech va me l’envoyer par courrier? je pose la question à Banggood! J’ai positionné les extruders sur des blocs et placer les supports filaments différemment pour simplifier l’opération de chargement filament. Photos incluses Positions des extruders et le plateau sans la plaque de verre.

    Comments
    Show Original
  • Lello
    BR
    20/03/2019

    Where can I buy the extruder block?!? I messed mine up!!!

    Comments (1)
    Show Original
  • 16/11/2019

    I have received the 3d printer with all parts and with some spare parts. In the Easy to assemble and easy to operate. Print quality is quite good. The motors are quiet. There is 3 fans that makes a bit of noise.

    Comments
    Show Original
  • 23/09/2019

    acabei de receber a impressora, vou montar e fazer os testes

    Comments (1)
    Show Original
  • 16/04/2020

    Great after the A10 the a10m

    Comments
    Show Original
  • 02/04/2020

    It's working fine.

    Comments
    Show Original
  • 15/12/2019

    Shipped from UK. Well packed with a lot of foam inside. The glass bed isn't included, as described, but you may order original glass bed or substitute like this: https://www.banggood.com/Creality-3D-Ultrabase-2352353mm-Glass-Plate-Platform-for-Ender-3-MK2-MK3-Hot-bed-3D-Printer-Part-p-1350129.html?rmmds=myorder&cur_warehouse=CN This glass plate fits perfect to the printer, because actual size of the heated bed is 235x235mm.

    Comments
    Show Original
Show:

    Total 0 pages

    Go to page

    Go

    You might be interested in

    recommendation for you
    • US$379.00
    • US$189.00
    • US$519.00
    • US$899.00
    • US$499.00
    • US$159.99
    • US$319.00
    • US$359.00
    • US$379.00
    • US$259.00
    • US$399.00
    • US$299.00
    • US$459.00
    • US$599.00
    • US$799.00
    • US$189.00
    • US$299.99
    • US$77.99