Customer Reviews

4.84 out of 5
Write a Review
  • All Reviews (130)
  • Image (14)
  • Video (0)
  • All Star
    • All Star(130)
    • 5 Star(118)
    • 4 Star(8)
    • 3 Star(1)
    • 2 Star(1)
    • 1 Star(2)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
  • cheongk
    2016-10-16 00:57:51

    Summary: Very nice kit, pretty easy to build and works well. I was fortunate to get all components, no major issue during the built except that I soldered the USB connector the wrong way around and had to take it out again. Everything else worked the first time. Need to follow all instructions. Tips: 1) Sort out the components first before starting any soldering. See attached picture. I just poked all the components on a piece of styrofoam. 2) Install all the components as per the order in the instructions.

  • 2016-05-19 08:21:17

    Неплохой DIY комплект для проверки своих навыков начинающим радиолюбителям. Более того, DSO 068 — это не просто набор для обучения, но и в итоге получился неплохой портативный осциллограф-частотомер для повседневного использования. Набор для начинающих радиолюбителей. Для профессионалов

  • titou04
    2016-04-16 15:38:06

    je me suis lancé a commander ce kit d'oscillo numérique car il présentais des caractéristiques honorables au niveau bande passante de 3 MGH ; le kit reçu , est très bien fournis et aucun éléments n'étaient manquant , par contre au montage , je me suis vite heurté a la miniaturisation de ce module , qui nécéssite attention , rigueur, précision ect vous dit ça car j'ai quand même passé ma vie dans l'électronique et la difficulté se résume a ++++++ !...donc faut déja être

  • amkza
    2018-01-08 04:05:28

    I received the kit and put it together. No issues. Everything is as expected. Have not used it yet for anything other than testing but everything checked out okay.

  • wazad11
    2016-04-08 06:53:55

    I enjoyed assembling and tuning the oscilloscope. The assembly guide is good. Very helpful was the pcb silkscreen schematics found in the section of the JyeTech forum dedicated to DSO068! I couldn't managed yet to connect to JyeLab! In rest, as standalone, it is functioning ok!

  • seldon
    2017-09-10 17:58:32

    Before receiving the product, the reading of the forum of JYETECH and the visualization of the videos existing on youtube about the same, allowed me to prepare me to order and measure the components as indicated in the assembly guide, on arrival, greatly facilitated the assembly , and of the registered faults only the fault of the crystal hapened, i was ready with one by hand, from there in the end, everything well. After the final test, a firmware upgrade was done by usb and the JYELAB was installed

  • LoopoS1
    2017-02-21 07:34:13

    The perfomance is ok up to the 150k or so. I like it's FFT mode. Only disadvantage I observe - slight freeizng near the 0.5 uS and lack of the RMS readings. And yes, I know, this is a toy. 1st photo: AD797 oscillating on the unity gain. 2nd photo: 66 kHz interference on the mains between N and PE.

  • stseb
    2017-02-21 09:19:24

    If you need pocket osciloscope it's worth the money. You have consider its limitations: bandwidth and screen. Like you can see in photo cheeper osciloscope has nice crisp screen, and this one has something from XX century.:) You have to buy battery seperately, o simply use power bank. Quality isn't perfect at best. U3 was badly soldered and scope had lots of noises. After resoldering noise level droped. Capacitor C8 broke when i was trying to calibrate scope. I changed it, but I can't calibrate scope

  • Andyg
    2016-11-02 00:59:00

    Super impressed with this little kit. Firstly I have been in the electronics game for a looooong time. This kit comes with reasonable English instructions with all the super fiddly bits already placed for you. So long as you follow the instructions, take your time, and verify values with a meter, you will be just fine. The features for such a simple device are great and most importantly this is a usable bit of test kit. The Size makes this a must for guys like me who are often out on the road and

  • 2016-05-28 06:51:15

    I just want my kit made first before starting the welding I did an inventory of rooms and to my desolation in brand resistors, inductors and capacitors for the rest it seems complete but another question how to know the value of disk capacitors for tagging does not differentiate I joined you a picture of the whole kit as received, I've done better now for you to see all the elements I voufrais can still realize you can send me the complete lot of resistance inductors and as capacitor qque tell me


    Go to page


    You might be interested in

    recommendation for you
    • US$5.99
    • US$3.99
    • US$19.99
    • US$23.99
    • US$2.99
    • US$64.99
    • US$27.99
    • US$4.49
    • US$26.99
    • US$8.99
    • US$16.99
    • US$4.99
    • US$4.99
    • US$15.99
    • US$36.99
    • US$8.19
    • US$3.99
    • US$119.99