Customer Reviews

4.6 out of 5
See all 15 reviews
Write a Review
  • All Reviews (15)
  • Image (3)
  • Video (0)
  • All Star
    • All Star(15)
    • 5 Star(12)
    • 4 Star(2)
    • 3 Star(0)
    • 2 Star(0)
    • 1 Star(1)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (United States)
|
Show Original

A part of the review has been auto-translated.

  • 31/07/2021

    Delivery 2 days, 10 minutes build - up, 15 minutes after delivery the first print in super quality, still questions 👍👍👍

    Comments
    Show Original
  • 21/08/2021

    Fantastic machine. I set it up right away and have been using it for a week now. Very simple to use and have had no issues at all. I have been printing quite a few items and not done any modifications or updates.

    Comments
    Show Original
  • 27/07/2021

    No shipping damage

    Comments
    Show Original
  • 21/08/2021

    Unpack, assemble and start printing. But now from the beginning. The printer was very well and safely packed in a lot of foam inlays in the carton. When removing the individual components, however, it is important to note that the base and portal are connected by a cable. The assembly was done quickly, because only the base and portal can be connected by four screws. Now plug in all the cables and it could start. As a precaution I checked all the visible screws again and pulled some carefully. At the first car levels I noticed then that the hotend was screwed on quite loosely and thus the car levels did not work properly. So carefully loosened the plastic housing and tightened the bolts of the Hotend. After the housing was fixed again, the car leveling worked without any problems. The first test print of the owl from the SD card actually looked very good. Now connected the printer to the Raspberry PI 4 B via USB cable. Octopi runs on the Raspberry. from Cura, version 4.10 I have finished and printed the first models with the given profile of the ANY Viper. The result was good but could be better. So the profiles of my Anycubic I3 Mega S adjusted and reprinted. Now the result was perfect from my point of view. Conclusion: The Anycubic Viper is a very beginner-friendly printer and does what you are promised. With the Anycubic I3 Mega S it was a lot harder to adjust the printer with the level screws until perfect results were achieved. The adhesion of the prints on the print bed is so good that sometimes it is a little hard to remove the skirt lines from the print bed. The only thing that really disturbs me is the extremely loud fan of the PSU. I will have to do another upgrade.

    Comments
    Show Original
  • 18/07/2021

    love this 3d printer. touch screen very easy to use. auto bed levelling is fantastic. from never had a 3d printer before I was printing my first print in minutes. fan on motherboard is quite noisy

    Comments
    Show Original
  • 24/07/2021

    Esse to assemble

    Comments (1)
    Show Original
  • 14/09/2021

    Shipping faster.

    Comments
    Show Original
  • 22/08/2021

    system a little too closed, difficulty to fine - tune the settings.

    Comments (1)
    Show Original
  • 13/08/2021

    fast delivered best price on the market

    Comments
    Show Original
  • 11/08/2021

    Super fast delivery, printer prints out of the box...

    Comments
    Show Original
Show:

    Total 0 pages

    Go to page

    Go
    recommendation for you
    • US$209.00
    • US$99.99
    • US$429.99
    • US$999.99
    • US$329.00
    • US$659.99
    • US$459.00
    • US$249.99
    • US$369.99
    • US$529.00
    • US$339.99
    • US$569.99
    • US$259.99
    • US$164.99
    • US$399.00
    • US$499.99
    • US$399.00
    • US$259.00