I use this to charge 6 500mah lipos that I use with my hubsan mini quad. You have to do a minor modification to the cable in order to charge the batteries as if they were a 6S pack. You will notice that in the connector, in the ends there should a red wire, and in the other side a black wire. You should cut the INSULATION ONLY of them, and them use the alligator clip and connect the RED with RED (+) and BLACK with BLACK (-) Do not power your charger, first connect the balance cable to the 6S socket in your charger, attach the alligator clips in the + and - cables (opposite outer ends of the connector), and then the batteries very carefully not to reverse polarity, and then turn on the charger. Since 6 500mah batteries in series should be a 3000mah 6S lipo, I would charge it at 3.0A (1C), but I received a advice to use 0.5A instead (1C of the original single 1S 500mah cell). I still don't know if I can charge them with 3A, but I rather play safe and use the 0.5A instead. I'll upload some pictures to have a better idea about the cable. Cheers!

I use this to charge 6 500mah lipos that I use with my hubsan mini quad. You have to do a minor modification to the cable in order to charge the batteries as if they were a 6S pack. You will notice that in the connector, in the ends there should a red wire, and in the other side a black wire. You should cut the INSULATION ONLY of them, and them use the alligator clip and connect the RED with RED (+) and BLACK with BLACK (-) Do not power your charger, first connect the balance cable to the 6S socket in your charger, attach the alligator clips in the + and - cables (opposite outer ends of the connector), and then the batteries very carefully not to reverse polarity, and then turn on the charger. Since 6 500mah batteries in series should be a 3000mah 6S lipo, I would charge it at 3.0A (1C), but I received a advice to use 0.5A instead (1C of the original single 1S 500mah cell). I still don't know if I can charge them with 3A, but I rather play safe and use the 0.5A instead. I'll upload some pictures to have a better idea about the cable. Cheers!

I use this to charge 6 500mah lipos that I use with my hubsan mini quad. You have to do a minor modification to the cable in order to charge the batteries as if they were a 6S pack. You will notice that in the connector, in the ends there should a red wire, and in the other side a black wire. You should cut the INSULATION ONLY of them, and them use the alligator clip and connect the RED with RED (+) and BLACK with BLACK (-) Do not power your charger, first connect the balance cable to the 6S socket in your charger, attach the alligator clips in the + and - cables (opposite outer ends of the connector), and then the batteries very carefully not to reverse polarity, and then turn on the charger. Since 6 500mah batteries in series should be a 3000mah 6S lipo, I would charge it at 3.0A (1C), but I received a advice to use 0.5A instead (1C of the original single 1S 500mah cell). I still don't know if I can charge them with 3A, but I rather play safe and use the 0.5A instead. I'll upload some pictures to have a better idea about the cable. Cheers!

Produit correcte. Fils 26AWG 200° isolant silicone. La longueur environ 15cm avec les prises.

Produit correcte. Fils 26AWG 200° isolant silicone. La longueur environ 15cm avec les prises.

Produit correcte. Fils 26AWG 200° isolant silicone. La longueur environ 15cm avec les prises.

If you want to use tis cable to charge you must solder a cable to the outer black cable and connect it to -. If you will charge 6 batteries you connect thr outer red to +. I connected one to the 6:e and one to the 4:th red (both are connected to the outer black) so now I can charde 6 or 4 batteries at the same time. I have numbered the battery Connections 1 to 6 starting with 1 at the end with the outer black.

If you want to use tis cable to charge you must solder a cable to the outer black cable and connect it to -. If you will charge 6 batteries you connect thr outer red to +. I connected one to the 6:e and one to the 4:th red (both are connected to the outer black) so now I can charde 6 or 4 batteries at the same time. I have numbered the battery Connections 1 to 6 starting with 1 at the end with the outer black.

If you want to use tis cable to charge you must solder a cable to the outer black cable and connect it to -. If you will charge 6 batteries you connect thr outer red to +. I connected one to the 6:e and one to the 4:th red (both are connected to the outer black) so now I can charde 6 or 4 batteries at the same time. I have numbered the battery Connections 1 to 6 starting with 1 at the end with the outer black.

Кабель нормального качества, провода мягкие. Для зарядки через IMAX B6 не подходит, так как у неё слабый балансир и нужно к данным проводам добавлять ещё 2 силовых. --- Good cable. But it's not for IMAX B6.

Кабель нормального качества, провода мягкие. Для зарядки через IMAX B6 не подходит, так как у неё слабый балансир и нужно к данным проводам добавлять ещё 2 силовых. --- Good cable. But it's not for IMAX B6.

Кабель нормального качества, провода мягкие. Для зарядки через IMAX B6 не подходит, так как у неё слабый балансир и нужно к данным проводам добавлять ещё 2 силовых. --- Good cable. But it's not for IMAX B6.

With a simple JST cable attached you will get a charging and balance cable for 6 lipos. I moded this with one part of a Dupond femal and three male cables and now iI am able to choose between 3 ,4.5 and 6 lipos charging/balancing.

With a simple JST cable attached you will get a charging and balance cable for 6 lipos. I moded this with one part of a Dupond femal and three male cables and now iI am able to choose between 3 ,4.5 and 6 lipos charging/balancing.

With a simple JST cable attached you will get a charging and balance cable for 6 lipos. I moded this with one part of a Dupond femal and three male cables and now iI am able to choose between 3 ,4.5 and 6 lipos charging/balancing.

top merci

top merci

top merci

отличный провод. провода мягкие силикон. рекомендую.

отличный провод. провода мягкие силикон. рекомендую.

отличный провод. провода мягкие силикон. рекомендую.

Good price, very useful cable for charging together up to 6 LiPo 1S cells. You need to solder additional cables for "+" and "-" depending on how many cells you are charging. You can also easily check all batteries voltage using LiPo tester as shown on my video.

Good price, very useful cable for charging together up to 6 LiPo 1S cells. You need to solder additional cables for "+" and "-" depending on how many cells you are charging. You can also easily check all batteries voltage using LiPo tester as shown on my video.

Good price, very useful cable for charging together up to 6 LiPo 1S cells. You need to solder additional cables for "+" and "-" depending on how many cells you are charging. You can also easily check all batteries voltage using LiPo tester as shown on my video.

26AWG - Slicone - perfect quality - Thanks Banggod - Must have for my x73 and walkera micro - 5 batterie at a time like a 5 battery - Because it's serial, let max amp on your charger at capacity of 1 battery. 1S 500mAH * 5 battery = charge at 500mAH.

26AWG - Slicone - perfect quality - Thanks Banggod - Must have for my x73 and walkera micro - 5 batterie at a time like a 5 battery - Because it's serial, let max amp on your charger at capacity of 1 battery. 1S 500mAH * 5 battery = charge at 500mAH.

26AWG - Slicone - perfect quality - Thanks Banggod - Must have for my x73 and walkera micro - 5 batterie at a time like a 5 battery - Because it's serial, let max amp on your charger at capacity of 1 battery. 1S 500mAH * 5 battery = charge at 500mAH.

Really like these, as enabling you to charge 6 batteries at once. I hade to solder two banana plugs to the most positive and the most negative lead, for my charger to accept it. Would be nice if this might be fitted from factory as all of my 3 chargers required it.

Really like these, as enabling you to charge 6 batteries at once. I hade to solder two banana plugs to the most positive and the most negative lead, for my charger to accept it. Would be nice if this might be fitted from factory as all of my 3 chargers required it.

Really like these, as enabling you to charge 6 batteries at once. I hade to solder two banana plugs to the most positive and the most negative lead, for my charger to accept it. Would be nice if this might be fitted from factory as all of my 3 chargers required it.