Very good power module. You can extend output voltage range (no load to full load) by changing R20 to 1.2kOm (low voltage limit ~9V) and VR1 to 4.7kOm (trimmer - high voltage limit ~33V). Under 8V not work stable and breakdown voltage of output capacitors is 35V !!!

Very good power module. You can extend output voltage range (no load to full load) by changing R20 to 1.2kOm (low voltage limit ~9V) and VR1 to 4.7kOm (trimmer - high voltage limit ~33V). Under 8V not work stable and breakdown voltage of output capacitors is 35V !!!

Very good power module. You can extend output voltage range (no load to full load) by changing R20 to 1.2kOm (low voltage limit ~9V) and VR1 to 4.7kOm (trimmer - high voltage limit ~33V). Under 8V not work stable and breakdown voltage of output capacitors is 35V !!!

Very good Power Supply. It work very stable. If you need wide range of output voltage (9V to 33V) - change R40 to 1.2kOm and VR1 to 4.7kOm trimmer . (Attention - you will null warranty after doing this activities)

Very good Power Supply. It work very stable. If you need wide range of output voltage (9V to 33V) - change R40 to 1.2kOm and VR1 to 4.7kOm trimmer . (Attention - you will null warranty after doing this activities)

Very good Power Supply. It work very stable. If you need wide range of output voltage (9V to 33V) - change R40 to 1.2kOm and VR1 to 4.7kOm trimmer . (Attention - you will null warranty after doing this activities)

- Correct quality - Works very well - Adjustable power supply from 16 to 28 VDC

- Correct quality - Works very well - Adjustable power supply from 16 to 28 VDC

- Correct quality - Works very well - Adjustable power supply from 16 to 28 VDC

Al extraerlo de su caja se aprecia que recibió un fuerte golpe durante el transporte, solo hay que ver como esta el precinto de garantía, lo he probado y funciona, pero tendré que intentar enderezar las chapas del chasis, aviso que tendré que romper el precinto de garantía. Ver las fotos.

Al extraerlo de su caja se aprecia que recibió un fuerte golpe durante el transporte, solo hay que ver como esta el precinto de garantía, lo he probado y funciona, pero tendré que intentar enderezar las chapas del chasis, aviso que tendré que romper el precinto de garantía. Ver las fotos.

Al extraerlo de su caja se aprecia que recibió un fuerte golpe durante el transporte, solo hay que ver como esta el precinto de garantía, lo he probado y funciona, pero tendré que intentar enderezar las chapas del chasis, aviso que tendré que romper el precinto de garantía. Ver las fotos.

very good quality In the standard set to 220V. Connect the cables and lets go!

very good quality In the standard set to 220V. Connect the cables and lets go!

very good quality In the standard set to 220V. Connect the cables and lets go!

t's worth having gotten dented one of the right flaps at the location where the trim RV is. usually have arrived in conditions.

t's worth having gotten dented one of the right flaps at the location where the trim RV is. usually have arrived in conditions.

t's worth having gotten dented one of the right flaps at the location where the trim RV is. usually have arrived in conditions.

Although without a fan, it does a good job to drive my CNC xPro controller and four steppers (3x NEMA 23 and 1x NEMA 17) along with a few bling. Pictures and video will follow once I clean up my setup. A few pictures already available at : http://www.openbuilds.com/builds/myox-a-4-x-2-ox-cnc-with-potential.915/

Although without a fan, it does a good job to drive my CNC xPro controller and four steppers (3x NEMA 23 and 1x NEMA 17) along with a few bling. Pictures and video will follow once I clean up my setup. A few pictures already available at : http://www.openbuilds.com/builds/myox-a-4-x-2-ox-cnc-with-potential.915/

Although without a fan, it does a good job to drive my CNC xPro controller and four steppers (3x NEMA 23 and 1x NEMA 17) along with a few bling. Pictures and video will follow once I clean up my setup. A few pictures already available at : http://www.openbuilds.com/builds/myox-a-4-x-2-ox-cnc-with-potential.915/

I just received this 24V 10A SMPS and tested the output voltage with my digital multimeter which was 24V as described. I was kind of surprised to find that it does not have a fan inside which was rather unusual for an SMPS. Although it was described as an SMPS for LED lights, I intend to use it for supplying power for my CNC or 3D printer project. And even though I gave all 5 stars, I do not know yet how long this SMPS will last but it appears to be OK. I will update later if I find more.

I just received this 24V 10A SMPS and tested the output voltage with my digital multimeter which was 24V as described. I was kind of surprised to find that it does not have a fan inside which was rather unusual for an SMPS. Although it was described as an SMPS for LED lights, I intend to use it for supplying power for my CNC or 3D printer project. And even though I gave all 5 stars, I do not know yet how long this SMPS will last but it appears to be OK. I will update later if I find more.

I just received this 24V 10A SMPS and tested the output voltage with my digital multimeter which was 24V as described. I was kind of surprised to find that it does not have a fan inside which was rather unusual for an SMPS. Although it was described as an SMPS for LED lights, I intend to use it for supplying power for my CNC or 3D printer project. And even though I gave all 5 stars, I do not know yet how long this SMPS will last but it appears to be OK. I will update later if I find more.

予想以上に時間がかかった

se tardó más de lo que esperaba

予想以上に時間がかかった

ヨップ タイプ

tip yop

ヨップ タイプ