Necessary item to adjust servo rod length. Have no issues with the quality, all ok. // Необходимая штука для регулировки тяг сервомашинок. Проблем с качеством не было, всё хорошо.

Necessary item to adjust servo rod length. Have no issues with the quality, all ok. // Необходимая штука для регулировки тяг сервомашинок. Проблем с качеством не было, всё хорошо.

Necessary item to adjust servo rod length. Have no issues with the quality, all ok. // Необходимая штука для регулировки тяг сервомашинок. Проблем с качеством не было, всё хорошо.

Parfait pour des tiges de commande (métallique ou carbone) de faible diamètre

Parfait pour des tiges de commande (métallique ou carbone) de faible diamètre

Parfait pour des tiges de commande (métallique ou carbone) de faible diamètre

Стержни для фиксации тяг. металлические. С виду нормальные. Упакованы в полителеновый пакетик. Думаю должны хорошо служить.

Стержни для фиксации тяг. металлические. С виду нормальные. Упакованы в полителеновый пакетик. Думаю должны хорошо служить.

Стержни для фиксации тяг. металлические. С виду нормальные. Упакованы в полителеновый пакетик. Думаю должны хорошо служить.

сделано аккуратно

сделано аккуратно

сделано аккуратно

I received a couple of extra washers with my shipment of push rod adjusters after using two washers per adjuster. They're small, lightweight and a great way to fine tune your pushrod lengths. As everyone else says, use a drop of Loctite or superglue on the nut after you get it the way you want it so it doesn't loosen. Be sure to position them so you can get a #1 phillips screwdriver on the rod adjusting set screw. I may replace the phillips head screws with allen head setscrews to make adjusting easier. Some people put these on the servo arm. I prefer to put them at the control surface control horn.

I received a couple of extra washers with my shipment of push rod adjusters after using two washers per adjuster. They're small, lightweight and a great way to fine tune your pushrod lengths. As everyone else says, use a drop of Loctite or superglue on the nut after you get it the way you want it so it doesn't loosen. Be sure to position them so you can get a #1 phillips screwdriver on the rod adjusting set screw. I may replace the phillips head screws with allen head setscrews to make adjusting easier. Some people put these on the servo arm. I prefer to put them at the control surface control horn.

I received a couple of extra washers with my shipment of push rod adjusters after using two washers per adjuster. They're small, lightweight and a great way to fine tune your pushrod lengths. As everyone else says, use a drop of Loctite or superglue on the nut after you get it the way you want it so it doesn't loosen. Be sure to position them so you can get a #1 phillips screwdriver on the rod adjusting set screw. I may replace the phillips head screws with allen head setscrews to make adjusting easier. Some people put these on the servo arm. I prefer to put them at the control surface control horn.

Норм, поставил на модель

Норм, поставил на модель

Норм, поставил на модель

when i pull the nut to strong, the linkage stopper does not rotate anymore when the servo moves. but when i loosen the nut, it starts to become more and more loose and i am afraid it might fall off in flight... But when you thighten them up every now and then you should be just fine.

when i pull the nut to strong, the linkage stopper does not rotate anymore when the servo moves. but when i loosen the nut, it starts to become more and more loose and i am afraid it might fall off in flight... But when you thighten them up every now and then you should be just fine.

when i pull the nut to strong, the linkage stopper does not rotate anymore when the servo moves. but when i loosen the nut, it starts to become more and more loose and i am afraid it might fall off in flight... But when you thighten them up every now and then you should be just fine.

Tout va bien.

Alles bestens

Tout va bien.

parfait banggood

perfect banggood

parfait banggood

super

super

super