Customer Reviews

4.76 out of 5
See all 70 reviews
Write a Review
  • All Reviews (70)
  • Image (7)
  • Video (1)
  • All Star
    • All Star(70)
    • 5 Star(62)
    • 4 Star(3)
    • 3 Star(3)
    • 2 Star(0)
    • 1 Star(2)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (United States)
|
Show Original

A part of the review has been auto-translated.

  • 08/04/2017

    It works well. After reading about possible 5v bec issues, Im not using the 5volt regulator at all. Using Spektrum sat. on the 3.3 volt regulator. No buzzer, no leds. Powering board with 2 cells on vbat. Using my external bec for cam and vtx. Came with betaflight preflashed which is nice. OSD is awesome! Flight is great, and no drift on prolonged hover. The only thing I was surprised by, was that the usb backfeeds through the b+ b- vbat connections, which will energize esc power, making frying something a risk if usb is used without a battery, or opening up the vbat b+ so it wont backfeed, or install a diode on vbat b+. This is really only a pain when you want to cal escs. Otherwise be aware, you can start motors on usb power if you dont do something to prevent it. Lastly, be ready to turn down your 2.5mm spacers to clear things on the top side. Very tight around usb and sat port. Im going to get another.

    Comments
    Show Original
  • 26/08/2017

    Great little Flight Controller! I installed it in a Eachine racer 130, to replace the original combo board that combined FC+PDB. This new FC has a faster F3 chip and the OSD is entirely configured in betaflight so it's convenient. At first it didn't work properly "as received" with BF 3.1.0 : It didn't save its settings and did other bizarre things. My best solution was to reflash it. I struggled a bit but finally with some youtube help and the Zadig tool (com port emulator in windows) I was able to flash BF 3.1.7 !!! After that, the FC was FANTASTIC. It does everything RIGHT. I highly recommend it !!! And I love the OSD !!!

    Comments
    Show Original
  • 30/08/2017

    sorry for late update. just got to wire this baby up to a test frame. and here she is. yes she flies 👍

    Comments
    Show Original
  • 24/03/2017

    На нем нет BOOT контактов (я не понял где). но все просто. поставляется с прошитым Бетафлаем. Для перепрошивки (обновления) - подключаем к компу, входим в BF конфигуратор, там в CLI , пишем DFU и ввод. Контроллер переходит в DFU режим (там где выбор порта). Далее качаем актуальную прошивку для OMNIBUSa , нажимаем "прошить" и радуемся )).

    Comments
    Show Original
  • 06/03/2017

    I had a big issue with my old 36x36mm board + a power board to control my 210 small multicopter. With this board everything workedout perfectly. The basic cableling of the ESC's is easy, just need to cut the wires the right lenght, even remove ground line from the control link and solder the ppm signal directly on the board in the middle of the 2 power connections of each ESC. Battery voltage is included even if not really described in the product specs. I was just missing the information how to setup SBUS inside Betaflight, sorted out it had to go to UART3. Ready to fly after 2 days

    Comments
    Show Original
  • 30/06/2017

    OSD entièrement pris en charge, 8k .raiment petit et léger. Il faut quelques compétences de soudure, car certains points sont très proches. La qualité semble bonne. Incroyable pour les minuscules quads.

    Comments
    Show Original
  • 07/03/2017

    Betaflight OSD fully supported, 8k capable.. really small and light. Takes some decent soldering skills, however, since some points are very close together. Soldering quality looks good. Awesome for tiny quads.

    Comments (3)
    Show Original
  • 17/07/2017

    Yeah, my workflow is a little more involved with this cos' I insist on using M3 hardware and this fella comes with M2.5 holes so I have to bore those out accordingly. I also make it a point to remove the annoying micro connector, but, really, that is its only sin. Otherwise, its been nice flying these FCs on my micros so far and will continue to use these for future builds.

    Comments
    Show Original
  • 28/10/2017

    a very goog and small Flightcontroller for betaflight and 80mm frame

    Comments
    Show Original
  • 21/07/2017

    Updated it to latest Betaflight with no problems. Relatively easy to solder. Works well in Firer 110 frame. Great to have OSD. Would have been nice, if it was possible to use M3 standoffs instead of M2.5.

    Comments
    Show Original
Show:

    Total 0 pages

    Go to page

    Go
    recommendation for you
    • US$39.99
    • US$33.50
    • US$89.99
    • US$17.99
    • US$79.99
    • US$57.99
    • US$69.99
    • US$16.99
    • US$6.00
    • US$58.99
    • US$64.99
    • US$62.99
    • US$13.99
    • US$24.99
    • US$69.90
    • US$53.99
    • US$69.99
    • US$95.99