If you need the Supporting Shell for this kit, please check this, http://www.banggood.com/Supporting-Shell-For-DIY-M12864-Graphics-Version-Transistor-Tester-Kit-p-989949.html
If you need the chip of this kit: >>>1002733<<<
Product title marked "DIY kit" of both parts, you need your own assembled by soldering, to demonstrate for convenience, the main products picture is a physical map, the second picrure are all parts that you receive, be sure to pay attention to distinguish
1. Resistors, capacitors, inductors, diodes, transistors, SCR, and most commonly used devices will automatically recognize and measure
2. The capacitance line measurement capacity and ESR
3. The square-wave generator
4.PWM pulse signal generator
5. Frequency meter function
6. The graphical display of measurement results, easy and intuitive, the whole function is performed by a rotary encoder switch control, easy to operate.
Power supply voltage: DC 5.5-12V
Working Current: 24mA @ 9V
PCB Size: 75 x 63 mm
1. One key measurement operation, auto power off delay. Shutdown current is only 20nA, support for battery operation
2: Automatic detection of PNP and NPN bipolar transistor, N, P-channel MOSFET, JFET field effect transistors, diodes, two diodes, thyristors, resistors, capacitors, inductors. Automatic detection of current amplification factor (B) Pin Definitions and turn-on voltage of the transistor and the emitter junction (Uf), Darlington transistor through a high threshold voltage and high current gain recognition.
3: Can detect bipolar transistors and MOSFET internal protection diode and displayed on the screen. It can be measured threshold voltage and the gate capacitance of the MOSFET.
4: Support two resistance measurements, the potential can also be measured. The highest resolution is 0.1 ohm resistance measurements, the highest measured value of 50M Euro.
5: Capacitance measurement range from 25pf to 100mF (100,000 UF). Resolution up to 1 pF. 0.09UF capacitance can be detected above the equivalent series resistance (ESR), a resolution of 0.01 ohms. To display the value of the capacitor voltage loss and increase the capacitance of a separate line ESR measurements, available online (on the circuit) direct measurement capacitor value and ESR, easy maintenance and troubleshooting capacitance.
6. Inductance measurement range of 0.01MH-20H, otherwise it will be displayed as resistance, if the inductor DC resistance higher than 2100 will be displayed as the European resistance.
7. Can two diode display symbols in the right direction, displaying the forward voltage drop. LED detected as a diode forward voltage drop higher than normal. Dual LEDs detected as double diode. Simultaneous detection LED flashes, very intuitive.
8. Each test of time is about two seconds, only the large capacitance and high inductance measurements will take a long time
1. The square wave signal generator, optional built-in within the range of 1HZ-2MHZ stall square wave signal;
2.PWM pulse signal generator for 1-99% of the pulse width modulated signal;
3. The frequency meter function, can test 1HZ-25KHZ or higher frequency signal (in this case a slight decrease in accuracy)
1 x DIY M12864 Graphics Version Transistor Tester Kit LCR ESR PWM
When you order from Banggood.com, you will receive a confirmation email. Once your order is shipped, you will be emailed the tracking information for your order's shipment. You can choose your preferred shipping method on the Order Information page during the checkout process. Banggood.com offers four different international shipping methods:
|Shipping from Chinese Warehouse|
|Airmail and register airmail||Area||time|
|United States, Canada, Netherlands, Spain, Germany, France, Japan, Republic of Korea, United Kingdom
||7-20 business days
||7-25 business days
|Belgium, Denmark, Finland, Ireland, Norway, Portugal, Sweden, Switzerland
||7-25 business days
|Brazil, Russia, Mexico
||15-35 business days
|Other countries||7-25 business days|
|Priority Direct Mail||Austria, Belgium, Denmark, Finland, France, Germany, Greece, Italy, Netherlands, Portugal, Spain, Sweden||7-12 business days|
|United States, United Kingdom||7-12 business days|
|Australia||6-9 business days|
|Japan Direct Mail||Japan||5-8 business days|
|EMS||7-15 business days to worldwide|
|Expedited Shipping||5-8 business days to worldwide|
NOTE: Netherlands Direct Mail has been combined into the Priority Direct Mail. If you are in a European country; simply choose Priority Direct Mail and it will be shipped via Netherlands Direct Mail.
*Expedited shipping can not be used for PO Box addresses
|Shipping From Local Warehouses|
|EU Warehouses||UK: usually 3-6 business days|
Other EU countries: usually 7-10 business days
|US Warehouses||USA: usually 3-6 business days |
Other American countries: usually 7-10 business days
Shipping from your local warehouse is significantly faster. Some charges may apply.
In addition, the transit time depends on where you're located and where your package comes from. If you want to know more information, please contact the customer service. We will settle your problem as soon as possible. Enjoy shopping!
This warranty and return policy are only available for the sub categories of Arduino SCM & 3D Printer Acc, Electronic Accessories & Gadgets .
Within 180 days
If there are any product quality problems which are not caused by artificial factors such as dis-assembly, misuse, drops or falls, water damage, un official firmware or software modifications or any others causes of damage, we will cover the actual postage (according to the receipt you provided) only if it cost less than $40 (USD).
If damage occurred such as the display screen is broken then we can not offer warranty service. If you still would like to repair it, you can send the unit back to us. We will help by forwarding the item (if repairable) to the manufacturer for repair. You pay for all the shipping cost and the repair cost in this situation. If there is any other cost incurred during the process, it will be at your expense as well. We will send you a bill to show you the details of all costs before we send the unit back to you.
After 180 days from shipment
Any warranty service for any eBook reader will be rejected after the 180 day period has expired.
DOA (Dead on Arrival) Items
If the product (expect DIY kits) arrived broken you need to contact with us within 3 days from the day you receive the package. Then follow the 3 Day Product Guarantee.
About Unsatisfactory Products
If you are not happy for any reason with your purchase then you can return it within 3 days of receipt for a full refund minus the shipping charges incurred by us or an exchange. You will be required to cover shipping cost both ways if the return is not a result of our error. Please make sure the item you send back to us is in the original packaging and the merchandise is in the same condition as when you received it.
E-Book Reader Problem
If there are E-book reader after-sale problems ,please kindly provide us with proof as below:
- Product ID number.
- Order number.
- Photo, video, screenshot.
- Description of the item problem.
We will confirm the photos are valid and solve your problem . If you can not offer us detailed videos or valid photos we can not help to solve your problem.
- Please read the descriptions carefully and clearly before purchasing. If the descriptions are not clear enough, please feel free to contact us .
- Visual confirmation is a requirement of your service policy. If you cannot provide a clear video or valid photos we cannot help to deal with product problems.
- This category( Arduino SCM & 3D Printer Acc)includes many DIY kits. Our technical service can only be a guide. We can do nothing to help and we are not responsible for the damage caused by incorrect welding, construction or any circuit damages. We recommend you have some knowledge of electronics before purchasing any of our DIY kits.
- If you find the product is damaged, please do not disassemble it privately (such as e-books, programmers, signal logic analyzers and other prebuilt items). If you disassemble it privately it is difficult to determine if the problem was caused by disassembly or due to manufacturer fault. Please do not open items up as we do not provide any warranty service on and disassembled items.